Opel Movano · Stage 1

Opel Movano 2.3 DCi Stage 1 Remap

Name: Opel Movano 2.3 DCi Stage 1 Remap
Brand: Opel

On Opel Movano 2.3 DCi diesel engines a Stage 1 remap recalibrates the fuel quantity, injection timing, boost pressure and torque limiter maps. No hardware is changed and the original software is backed up. The same engine is sold with different stock outputs across generations, so the gain depends on your version.

How much bhp does Opel Movano 2.3 DCi chip tuning add?

It depends on the generation and the stock output. 2.3 DCi engines with 110–170 bhp reach 140–195 bhp with a Stage 1 remap; the largest gain is +50 bhp (B 2.3 DCi Bi-turbo (Euro 6) 145hp). Pick your version in the table below.

Book an appointment Opel Movano: all engines & Stage 1

Opel Movano 2.3 DCi: Stage 1 figures by generation and year

Year / chassis: (B) - 2016 - 2018

Engine	Power	Torque	Gain
Opel Movano 2.3 DCi (Euro 6) 110hp	110 → 140 bhp	285 → 345 Nm	+30 bhp
Opel Movano 2.3 DCi (Euro 6) 130hp	130 → 160 bhp	340 → 390 Nm	+30 bhp
Opel Movano 2.3 DCi Bi-turbo (Euro 6) 145hp	145 → 195 bhp	360 → 420 Nm	+50 bhp
Opel Movano 2.3 DCi Bi-turbo (Euro 6) 165hp	165 → 195 bhp	380 → 420 Nm	+30 bhp
Opel Movano 2.3 DCi (Euro 6) 170hp	170 → 195 bhp	380 → 420 Nm	+25 bhp

In Taiwan

Where can this be done near you?

GP Power ECU applies the software at its workshop in Hukou, Hsinchu, using EcuPrime-developed files; workshops can also order the file directly.

ENGINE FAMILY

About the common-rail turbo diesel engine

This vehicle uses a common-rail turbo diesel engine. In this technology fuel is sprayed from a shared high-pressure rail through electronically controlled injectors, and the ECU constantly manages injection quantity, timing and boost pressure.

How a Stage 1 remap works on the Opel Movano 2.3 DCi

A Stage 1 remap recalibrates injection quantity, rail pressure, boost pressure and torque limiters together. Torque gains are clear on diesels and pull improves at low and mid revs. Smoke, exhaust temperature and turbo speed limits are kept.

Pre-remap checklist

Injector condition and leak-off test.
Leaks in the turbo and boost circuit.
EGR valve and, on DPF cars, the differential pressure sensor.
Clutch and dual-mass flywheel; the extra torque can cause slipping.

Catalogue figures assume a healthy engine; diagnosis first, then software.

This section is based on GP Power ECU workshop experience; the power and torque figures come from the catalogue measurement above.

Frequently asked questions

How much bhp does Opel Movano 2.3 DCi chip tuning add?

It depends on the generation and the stock output. 2.3 DCi engines with 110–170 bhp reach 140–195 bhp with a Stage 1 remap; the largest gain is +50 bhp (B 2.3 DCi Bi-turbo (Euro 6) 145hp). Pick your version in the table below.

What is the difference between Stage 1 and Stage 2 on the Opel Movano 2.3 DCi?

Stage 1 is software only: no part of the car is changed and the figures in the table apply to this software. Stage 2 is software prepared for hardware changes such as the exhaust, intercooler or intake; the hardware comes first, then the software.

Will chip tuning damage the engine?

No. Values stay inside the safety margin the manufacturer leaves; engine, gearbox and turbo limits are not exceeded. Every file is verified with a road test and data logging. If the car needs maintenance first (worn injectors, blocked filter, weak clutch) we tell you before starting.

Will my fuel consumption go up?

With the same driving style it usually drops, because you hold the same speed at lower revs and less throttle. If you use the extra power, consumption naturally rises. It is down to your right foot.

How long does it take? Do I leave the car?

Most cars take 1–2 hours and you get the car back the same day; no need to leave it. Some models need the ECU removed, which takes longer — we tell you when booking.

Can I go back to stock later?

Yes. The original file is read and archived before any work. We restore the factory software free of charge whenever you ask.

What is checked on the Opel Movano 2.3 DCi before remapping?

Before working on the common-rail turbo diesel engine we check: Injector condition and leak-off test. Leaks in the turbo and boost circuit. EGR valve and, on DPF cars, the differential pressure sensor. Clutch and dual-mass flywheel; the extra torque can cause slipping. If something needs attention, maintenance comes first; the remap is applied to a healthy engine.